吸附式干燥机

吸附式干燥机

◆产品特点 Product features

※具有稳定一致的出气压力和露点

1.吸附塔之高度与直径经实验结果精密计算，塔床阻力小，保证了压缩气体干燥剂5秒的接触时间，满足成品气的露点要求。

2.30％的干燥剂余量，用于补偿干燥剂的自然老化，确保干燥。

3.大型扩散器，确保气流均匀通过干燥剂层，消除沟流现象。

※再生气量损耗小于14％

1.##的机筒设计，保存100％的吸附热量，储存的热量用于增加再生阶段的再生气温度，提高设备的解吸能力，使得再生更彻底。

2.干燥和再生采用反向对流方案，湿空气流过干的吸附剂时效果*佳。再生气出口含湿量控制在亚饱和状态，使消声器及排气通道无结露之虑。

3.可根据干燥机的运行负载需求调节再生气用量，确保再生气流连续稳定，再生压力低至临界。

※干燥剂使用寿命长

1.合适的机筒尺寸，使气体通过干燥剂层的流速和时间保持*佳状态，充分发挥干燥剂的性能。

2.合理的系统配置，在气流进入机筒前，经高效除油处理及时清除气流中内含油物与重污染物，避免干燥剂层受污染。

※设备采用了新颖高品质电动及气动阀和先进可靠的全电子可编程序控制器，人机界面友好，自动连续显示双塔工况，循环周期现场可编，出厂设定10min。阀门寿命长达50万次动作。

※筒体内壁作冷镀锌防锈处理，10年不锈蚀。

※动作准确、性能稳定、操作简便，安装无需基础。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆主要技术参数 Main technical parameters